How Far Does a Swamp Cooler Need to Be From a Plumbing Vent or Flue?
The code distance between a swamp cooler and a plumbing vent, water heater flue, dryer vent or street: 10 ft unless the vent ends 3 ft above the intake, with worked rooftop and window cases.
Short answer
10 ft. The residential code requires a swamp cooler's air intake to be at least 10 ft from plumbing vents, appliance vents, chimneys, streets, alleys and parking lots, unless the intake sits 3 ft or more below the vent's opening. A gas vent through a wall, or a power vent, has the same 10 ft or 3 ft above rule. A dryer vent needs 3 ft. Kitchen and bath fans do not count.
Key takeaways
- IRC M1413.1 tells installers to place an evaporative cooler's air intake per Section R303.5.1, and R303.5.1 sets 10 ft from vents, chimneys, plumbing vents, streets, alleys, parking lots and loading docks.
- The one way out is height: no 10 ft gap is needed where the intake is 3 ft or more below the vent's opening. The plumbing chapter (P3103.5) says the same from the vent's side: 10 ft horizontally, or 3 ft above the top of the opening.
- A gas vent that ends on a wall must be 10 ft horizontally from a mechanical air inlet or 3 ft above it (Table G2427.8), and a power vent must be 3 ft above any forced air inlet within 10 ft (M1804.2.6). A window cooler is that kind of inlet.
- A dryer vent needs 3 ft in any direction unless the dryer's instructions say otherwise. The code does not count kitchen and bath exhaust as noxious, but Phoenix and Essick manuals still say to keep coolers away from kitchen exhausts.
- Measure from the vent opening to the nearest pad face, not to the middle of the cabinet. On a Champion 4001 DD that difference is about 17 in.
On this page
A swamp cooler's air intake has to be at least 10 ft from a plumbing vent, a water heater or furnace vent, or a chimney. That is the residential code's number, in Section R303.5.1 of the International Residential Code (IRC). The same 10 ft applies to streets, alleys, parking lots and loading docks. There is one way around it: height. The 10 ft gap is not needed where the cooler's intake sits 3 ft or more below the vent's open end. A dryer vent needs only 3 ft, and kitchen and bath fans do not count at all.
Below are the rules for each kind of vent, two worked cases, and how to tell whether a vent is behind a sewer smell. Where this fits in the whole job is in the swamp cooler installation guide.
What counts as the intake, and what counts as a vent
A swamp cooler pulls all of its air from outdoors. It draws that air through wet pads, then blows it into the house. Nothing is recirculated. So whatever drifts past the pads ends up inside. The Department of Energy's Building America code brief makes this point about direct coolers. Because they are "100% outside air systems," it says, "careful attention" has to go to "the location of any exhaust vents or anything else that could introduce odors or pollutants into the home."
The intake is every louvered side of the cooler where air enters the pads. On a rooftop downdraft cooler that is usually three or four sides of the cabinet. On a window or side draft cooler it is the louvered sides and back; the two layouts are compared in downdraft vs side draft coolers. Measure to the nearest pad face, not to the center of the cabinet. The intake is not the same as the open windows or relief dampers where air leaves the house, which venting and relief air covers.
The vents near a cooler come in three kinds:
- Plumbing vent. The open pipe that sticks up through the roof. It lets the drains breathe, and drain odors come out of it. Code requires it to end at least 6 in above the roof (P3103.1.1), so it is usually short.
- Appliance vent or flue. The pipe that carries exhaust from a gas water heater, furnace or boiler. A natural draft vent is a metal pipe through the roof with a cap. A power vent uses a fan, and a direct vent draws its own combustion air from outside. Both can end on a wall instead of the roof.
- Exhaust vent. A dryer vent, or a kitchen or bathroom fan outlet.
The rule, read from the code
The IRC's evaporative cooler section, M1413.1, lists how a cooler must be installed. One item is "so that air intake opening locations are in accordance with Section R303.5.1." That ties coolers to this rule by name. R303.5.1 reads:
"Mechanical and gravity outdoor air intake openings shall be located not less than 10 feet (3048 mm) from any hazardous or noxious contaminant, such as vents, chimneys, plumbing vents, streets, alleys, parking lots and loading docks."
It then sets out what is excused:
- Height. "The 10-foot (3048 mm) separation is not required where the intake opening is located 3 feet (914 mm) or greater below the contaminant source."
- Kitchen and bath exhaust. The exhaust from a home's "toilet rooms, bathrooms and kitchens shall not be considered as hazardous or noxious."
- Fuel-burning vents and dryers. Vents and chimneys for fuel-burning appliances follow the venting chapters, 18 and 24. Dryer ducts follow M1502.3.
This wording is the 2021 IRC as adopted in New Mexico and Utah. California's 2022 Residential Code has the same sentence. It sends fuel-burning vents and dryers to the California Mechanical Code instead.
Distance by vent type
| Source near the cooler | Minimum distance | Unless | Code section |
|---|---|---|---|
| Plumbing vent | 10 ft | Vent's open end is 3 ft or more above the top of the intake | R303.5.1, P3103.5 |
| Gas appliance vent ending on a wall (direct or non-direct vent) | 10 ft horizontally | Vent ends 3 ft or more above the intake | Table G2427.8, row I |
| Power vent (mechanical draft), other than direct vent | 10 ft | Vent ends 3 ft or more above the intake | M1804.2.6 |
| Natural draft vent or chimney through the roof | Keep 10 ft (the venting chapter sets roof height only) | Intake is 3 ft or more below the vent's top | R303.5.1, G2427.6.4 |
| Dryer vent | 3 ft in any direction | The dryer's instructions give a different distance | M1502.3 |
| Kitchen or bathroom exhaust fan | No code distance | Makers still say to keep away | R303.5.1 |
| Street, alley, parking lot, loading dock | 10 ft | Intake is 3 ft or more below the source | R303.5.1 |
Plumbing vents
The plumbing chapter states the same rule from the vent's side. Section P3103.5 says a drain vent shall not be "within 10 feet (3048 mm) horizontally" of an air intake opening "unless it is not less than 3 feet (914 mm) above the top of such opening." It also bars a vent less than 4 ft directly below an intake. Note the words "top of such opening." The 3 ft is measured from the top of the cooler's pads, not the bottom.
Gas water heater and furnace vents on a wall
Table G2427.8 in the fuel gas chapter sets clearances for vent ends that come through a wall. Row I covers "a mechanical air supply inlet." The clearance is "10 feet horizontally from inlet or 3 feet above inlet." It applies to both direct-vent and non-direct-vent ends. A cooler is a mechanical air supply inlet: its blower pushes outdoor air into the house. Row B is the one most people know, the distance from an openable window. For direct-vent ends it is only 6 to 12 in for appliances up to 150,000 Btu/h. A window cooler turns that window into row I, and row I is 10 ft.
Power vents
For mechanical draft systems other than direct vent, M1804.2.6 says "the vent terminal shall be located not less than 3 feet (914 mm) above a forced air inlet located within 10 feet (3048 mm)." That is the same pair of numbers again.
Vents and chimneys through the roof
Here the code text we read leaves a gap. R303.5.1 hands fuel-burning vents to the venting chapters. For a natural draft gas vent through the roof, those chapters set how high it ends. A vent up to 12 in across, at least 8 ft from a wall, ends 1 ft above a roof of up to 6/12 pitch (G2427.6.4). They set no distance from an air inlet. Keep a cooler 10 ft away anyway, with the same 3 ft height exception. It is the number R303.5.1 gives for vents and chimneys, and the one every other vent rule lands on. The cooler makers also say to stay clear. Phoenix's PD6802C manual says, "Do not locate unit near exhaust or vent pipes as odors or fumes may be drawn into cooler."
Dryer vents and kitchen fans
M1502.3 says a dryer duct ends where the dryer's instructions say. If they are silent, it ends "not less than 3 feet (914 mm) in any direction from openings into buildings." That is the code minimum. A cooler 3 ft from a dryer vent can still pull in warm, moist, linty air, so give it more room where you can.
Kitchen and bath fans are not "hazardous or noxious" under R303.5.1. The makers see it differently. Phoenix's BW5502 window cooler manual warns against places "where obnoxious odors or fumes may be drawn into cooler from vent pipes, kitchen exhausts, etc." Essick's CD30 manual says to "avoid installation near kitchen exhausts and vent pipes, so the cooler will not draw in fumes and odors." Neither gives a distance. Treat a kitchen hood as the makers do and keep the cooler off its downwind side.
Why "several feet" is the answer you usually hear
Most installation advice says to keep a cooler "several feet" from vents. That comes from the manuals. Five Phoenix and Essick manuals we read warn against vent pipes, and none of them gives a distance. The number is in the building code, which most homeowners never open. It is 10 ft, with the 3 ft height exception. Several feet is not enough for a plumbing vent or an appliance vent. It is only right for a dryer vent.
Worked example: a rooftop downdraft cooler near a 3 in vent stack
Take a Champion 4001 DD on a flat roof. Champion's sheet gives the cabinet as 34-1/8 in square and 34-1/2 in tall, with louvers on the sides. Suppose a 3 in plumbing vent comes through the roof, and someone measures 10 ft from it to the center of the cabinet.
That looks like it passes. It does not. The pad face is half the cabinet width closer, about 17 in. So the vent is about 8 ft 7 in from the intake, which is short of 10 ft.
There are two fixes:
- Move the cooler. Shift it about 1 ft 5 in farther from the vent, so the nearest pad face is 10 ft away. That moves the roof jack and the duct drop too, so check the framing first. The roof jack guide covers cutting the opening.
- Raise the vent. Suppose the stand puts the cabinet's top 40 in above the roof. The louvers run close to the top, so treat that as the top of the intake. The vent's open end must reach 40 + 36 = 76 in above the roof, about 6 ft 4 in. A vent at the 6 in code minimum would need about 70 in more pipe. That is plumbing work, and your city may want a permit for it.
On most roofs, moving the cooler is the simpler job. On a pitched roof, measure the height difference between the vent's top and the intake's top, not the height above the roof under each one.
Worked example: a window cooler beside a water heater vent
Suppose a house has a gas tankless water heater with a direct-vent end on the outside wall. The end is 5 ft to the side of a bedroom window, at about the same height. Before any cooler, that is fine: row B of Table G2427.8 asks only 6 to 12 in from an openable window for a direct-vent appliance up to 150,000 Btu/h.
Now put a Phoenix BW5502 window cooler in that window. The window is now a mechanical air supply inlet, and row I applies: 10 ft horizontally, or the vent end 3 ft above the inlet. At 5 ft to the side and the same height, it fails both.
The fix is a different window. Pick one at least 10 ft from the vent end, measured to the nearest pad face, or one at least 3 ft below it. Moving a gas vent is a job for a licensed pro. Phoenix's own manual says the same thing in plain words: install the cooler "in a window where only fresh outside air can enter." The window cooler installation guide covers the rest of the job.
Sewer smell: is it a vent?
A sewer or rotten egg smell from a cooler usually comes from the cooler itself. Bacteria grow in stagnant pan water and sludge. The swamp cooler smells guide covers that cause first. When the water is clean and the smell stays, look outside the cabinet.
- Check the pan and pads. Clean water, clean pads and a working bleed-off rule out the common cause. If they are not clean, start with the cleaning guide.
- Smell the house with the cooler off. If the smell is there with the cooler off, the source is inside the house, not the cooler.
- Find the nearest vent. Go up and look for plumbing vents, flues and fan outlets near the cooler. Measure from each opening to the nearest pad face.
- Compare the heights. A vent closer than 10 ft whose top is not 3 ft above the top of the pads fails the code. It is a likely source.
- Watch the wind. A vent smell comes and goes. It shows up when the wind blows from the vent toward the cooler, and fades when it shifts. Pan water smells all the time.
Treat a smell of exhaust from a gas appliance more seriously than sewer gas. Shut the cooler off and have the vent and the appliance checked before running it again.
Where this answer stops applying
These rules are the 2021 IRC as adopted in New Mexico and Utah, and California's 2022 Residential Code. Your city may use another edition or amend these sections. California also has its own Plumbing Code, which we could not read in full. The building department's adopted code is the one that counts, and a cooler job that needs a permit gets checked against it; see do you need a permit for a swamp cooler. The rules cover homes, not commercial buildings. They are written for installed coolers. A portable cooler on a patio is not covered, though the same air reaches it. Meeting the distance does not make a vent or flue safe. A cracked flue, a back-drafting water heater or a missing vent cap is a problem at any distance. The vent rules for gas appliances also defer to the appliance and vent makers' instructions, so read those for the exact model on your wall.
Frequently asked questions
How far should a swamp cooler be from a plumbing vent?
At least 10 ft from the cooler's intake, under IRC R303.5.1 and P3103.5. The only exception is height: the vent's open end can be closer if it is 3 ft or more above the top of the intake.
How far should a swamp cooler be from a water heater or furnace flue?
A gas vent that ends on a wall needs 10 ft horizontally from a mechanical air inlet such as a cooler, or must end 3 ft above it (Table G2427.8). A power vent needs 3 ft above any forced air inlet within 10 ft (M1804.2.6). For a vent through the roof, keep the cooler 10 ft away, the distance R303.5.1 sets for vents and chimneys.
Is several feet from a vent enough?
No. Cooler manuals say to avoid vent pipes but give no number, which is where 'several feet' comes from. The code number for a plumbing vent or appliance vent is 10 ft, or 3 ft of height.
Can I just make the plumbing vent taller?
Yes, that meets the rule if the vent's open end ends up 3 ft or more above the top of the cooler's intake. It is plumbing work, so check whether your city wants a permit for it.
How far should a swamp cooler be from a dryer vent?
3 ft in any direction under IRC M1502.3, unless the dryer maker's instructions give a different distance. That is a minimum, so more room is better.
Why does my swamp cooler smell like sewer gas?
If the pan water and pads are clean, a plumbing vent within 10 ft of the cooler is the likely source, and the smell will come and go with the wind. Otherwise the usual cause is bacteria in stagnant pan water.
Sources and further reading
- Evaporative Cooling: Code Compliance Brief, Pacific Northwest National Laboratory, Building America Solution Center (U.S. DOE)
- New Mexico Residential Code 2021 (2021 IRC), Chapter 3, Section R303.5.1 Intake Openings, UpCodes
- Utah Residential Code 2021 (2021 IRC), Chapter 14, Section M1413.1 Evaporative Cooling Equipment, UpCodes
- Utah Residential Code 2021 (2021 IRC), Chapter 31, Sections P3103.1.1 and P3103.5 Vent Terminals, UpCodes
- Utah Residential Code 2021 (2021 IRC), Chapter 24, Section G2427.6.4 and Table G2427.8 Vent Terminal Clearances, UpCodes
- Utah Residential Code 2021 (2021 IRC), Chapter 18, Section M1804.2.6 Mechanical Draft Systems, UpCodes
- Utah Residential Code 2021 (2021 IRC), Chapter 15, Section M1502.3 Dryer Duct Termination, UpCodes
- California Residential Code 2022, Chapter 3, Section R303.5.1 Intake Openings, UpCodes
- Phoenix BW5502 Window Evaporative Cooler Owner's Manual (installation), Phoenix Manufacturing, hosted by Appliance Factory Parts
- Phoenix PD6802C Owner's Manual (installation notes), Phoenix Manufacturing, hosted by Appliance Factory Parts
- Essick 15000 Series Owner's Manual (location), Essick Air Products, hosted by Appliance Factory Parts
- Essick CD30 and CD36 Installation Guide and Owner's Manual (location), Essick Air Products, hosted by Appliance Factory Parts
- Champion 3000, 4001 and 5000 DD/SD Specifications and Submittal Data (cabinet dimensions), Champion Cooler (Essick Air), hosted by Appliance Factory Parts