What Size Cover Do You Need for a Swamp Cooler?
Cabinet sizes for Champion, MasterCool, Hessaire and commercial coolers from their spec sheets, the cover each one takes, and why buying a cover 2 in oversized is the wrong rule.
Short answer
Buy a cover whose width and depth match the cabinet to the nearest inch and whose height is the same or up to about 2-1/2 in taller. A Champion 3000 (28-1/8 x 28-1/8 x 33-7/16 in) takes a 28 x 28 x 34 in cover, a Champion 4001 (34-1/8 x 34-1/8 x 34-1/2 in) a 34 x 34 x 36 in cover, and a MasterCool C51 (42 x 45 x 28 in) a 42 x 45 x 28 in cover.
Key takeaways
- Covers are sold by width x depth x height in inches, and the right one is the cabinet's own size rounded to the nearest inch, not a size picked from the CFM.
- In the Dial model pairings that can be checked against a spec sheet, cover width and depth run from 1/8 in under to 1 in over the cabinet, and cover height from 3/8 in to about 2-1/2 in over. The one exception is a 5000 DD cover that is shorter than the current cabinet.
- Model numbers that sound alike can need different covers: Dial pairs the Champion 4001 with a 34 x 34 x 36 in cover and the older Champion 4000 and 4500 with a 34 x 34 x 40 in one.
- The 12 in media versions of the MasterCool 51 and 71 are 4 in deeper than the 8 in versions (49 and 52 in), and no Dial cover is listed for them.
- Order the draft type that matches the cooler: Dial sells down draft and side draft covers as separate parts even where the nominal size is the same.
On this page
Buy a cover whose width and depth match the cooler cabinet to the nearest inch and whose height is the same or up to about 2-1/2 in taller. A Champion 3000 takes a 28 x 28 x 34 in cover, a Champion 4001 a 34 x 34 x 36 in cover, and a MasterCool C51 a 42 x 45 x 28 in cover. The cabinet sizes below come from the manufacturers' submittal sheets, and the covers from Dial Manufacturing's own model references, so each pairing can be checked to the fraction of an inch.
The cover is one of two seals a winterized cooler needs. Why the inside seal at the ceiling matters more, and how to fit both, is in swamp cooler covers; the whole fall shutdown is in the winterizing guide.
Cover size by cooler model
Covers are sold as width x depth x height in inches. Champion prints its cabinets as three lettered dimensions, the height and then two equal sides; MasterCool and Hessaire print height, width and depth. The table puts them all in cover order, W x D x H, so the two columns read the same way.
| Cooler | Cabinet (spec sheet) | Cover | Cover vs cabinet |
|---|---|---|---|
| Champion 3000 DD | 28-1/8 x 28-1/8 x 33-7/16 | 28 x 28 x 34, down draft (Dial 8912) | 1/8 in under each way, 9/16 in taller |
| Champion 3000 SD | 28-1/8 x 28-1/8 x 33-7/16 | 28 x 28 x 34, side draft (Dial 8728) | Same |
| Champion 4001 DD | 34-1/8 x 34-1/8 x 34-1/2 | 34 x 34 x 36, down draft (Dial 8929) | 1/8 in under each way, 1-1/2 in taller |
| Champion 4001 SD | 34-1/8 x 34-1/8 x 34-1/2 | 34 x 34 x 36, side draft (Dial 8745) | Same |
| Champion 5000 DD | 39 x 39 x 42-7/16 | 40 x 40 x 45, down draft (Dial 8950); see below | 1 in over each way, 2-9/16 in taller |
| Champion 5000 SD | 39 x 39 x 42-7/16 | 40 x 40 x 45, side draft (Dial 8767) | 1 in over each way, 2-9/16 in taller |
| MasterCool AD C51 | 42 x 45 x 28 | 42 x 45 x 28, down draft (Dial 8983) | Exact |
| MasterCool AD C71 | 42 x 48 x 34-5/8 | 42 x 48 x 35, down draft (Dial 8984) | Exact footprint, 3/8 in taller |
| MasterCool AS C71 | 42 x 48 x 34-5/8 | 42 x 48 x 35, side draft (Dial 8780) | Exact footprint, 3/8 in taller |
| MasterCool C5112 and C7112 | 42 x 49 x 28 and 42 x 52 x 34-5/8 | No Dial size listed | Measure; see below |
| Hessaire DX4800 | 32 x 31 x 25-5/8 | Hessaire CVR4800 | Maker's own cover |
| Hessaire DX6800 | 36 x 35 x 32 | Hessaire CVR6800 | Maker's own cover |
Where Dial names a model on a cover's product page, the table uses that cover: the 3000 and 4001 pairings are Dial's. Dial lists the MasterCool covers against the UltraCool ADA50 and ADA70 and the side draft ASA70 rather than the current C51 and C71, so those rows match by size: the C51 and C71 cabinets on MasterCool's sheet are exactly the footprints of those covers. The DD and SD versions of each Champion share one cabinet size on Champion's sheet, which is why the same nominal cover appears twice. Pads for the same cabinets are in swamp cooler pad sizes by model.
Why "buy it 2 in bigger" is the wrong rule
The common advice is to measure the cabinet and add an inch or two each way so the cover slides on easily. It persists because that is how covers for grills and furniture are sold. The cover makers' own pairings say otherwise. Across the eight covers in this article that Dial lists by model and that can be checked against a spec sheet, residential and commercial, cover width and depth run from 1/8 in under the cabinet to 1 in over it. Only the height runs consistently larger, by 3/8 in to 2-9/16 in. The one Dial listing that breaks the pattern, a 5000 DD cover, is short rather than oversized, and is covered below.
That fits how these covers are made. Dial's are 300d polyester with a drawstring ("strong draw rope") and brass grommets, and Classic Accessories' instructions close the cover with a "rip-n-grip strip" and "tie the two cords in the bottom hem together." The drawstring takes up a little extra height under the cabinet. Extra width and depth just hang as loose fabric for the wind to catch. So round the footprint to the nearest inch, and let the height run a little long, not short.
Pro tip: Measure around anything that sticks out of the cabinet. Dial makes an oversized version of its 42 x 43 x 28 in cover (8902) specifically "for units with junction box," for AeroCool models. A junction box, float valve inlet or pipe on one face adds to the width you have to clear.
Model names that point to the wrong cover
A cover is chosen by cabinet, and the model number does not always tell you which cabinet you have.
- Champion 4001 vs the older 4000 and 4500. Dial pairs the 4001 with a 34 x 34 x 36 in cover and the older Champion 4000 and 4500 (along with Marquis 4000, McGraw 4500, and Phoenix and Williams 4500 units from before the mid-1980s) with a 34 x 34 x 40 in cover. Same footprint, 4 in more height. On an older roof, measure the height before ordering.
- Champion 5000 DD. Dial's 40 x 40 x 31 in down draft cover (8948) is the one its catalog lists for the Champion 5000, 5500 and 6500 down draft. Champion's current sheet gives the 5000 DD a cabinet 42-7/16 in tall, so that cover would stop about 11 in short of the bottom. Dial does not say which cabinet generation the 8948 was made for. If your cabinet measures the current 42-7/16 in, the 40 x 40 x 45 in down draft cover (8950) is the Dial size that clears it.
- MasterCool 12 in media versions. The 12 at the end of C5112 and C7112 means 12 in media, and it makes the cabinet 4 in deeper than the 8 in version: 49 in instead of 45, and 52 in instead of 48. The nearest Dial cover, 42 x 48 x 35 in, is 1 in shallow for the C5112 and 4 in shallow for the C7112. Measure and look for a cover at least that deep.
The same lesson shows up in roof jacks, where the name on the box and the size of the cabinet part company; see what size roof jack a swamp cooler needs.
Down draft or side draft cover
Dial sells down draft and side draft covers as separate parts even where the nominal size is the same: 28 x 28 x 34 in is part 8912 for down draft and 8728 for side draft, and 34 x 34 x 36 in is 8929 and 8745. Order the type that matches how the cooler discharges. If you are not sure which you have, a down draft cooler sends air straight down through the roof and a side draft cooler through one side of the cabinet; downdraft vs side draft coolers shows both.
Commercial cabinets
Dial's largest covers line up with Champion's commercial cabinets just as closely as the residential ones do.
| Champion model | Cabinet (spec sheet) | Dial cover and its listed size range | Cover vs cabinet |
|---|---|---|---|
| 75/85 SD and 95 SD | 41-1/4 x 41-1/4 x 53-5/8 | 42 x 42 x 54 (8881), "Champion, Essick 7500-8500" | 3/4 in over each way, 3/8 in taller |
| 10/12 SD | 50 x 50 x 52-1/8 | 50 x 50 x 54 (8842), "Champion, Essick 10,500-12,500" | Exact footprint, 1-7/8 in taller |
| 14/21 SD | 62 x 62 x 59-3/4 | 62 x 62 x 62 (8882), "Champion, Essick 14,000-21,000" | Exact footprint, 2-1/4 in taller |
Dial files these three under down draft. These cabinets weigh from about 450 to over 1,000 lb running (see how much a swamp cooler weighs), and covering one is a roof job with the same fall risks as servicing it; the units themselves are covered in commercial and warehouse evaporative cooling.
How to measure a cooler you cannot identify
- Look for the plate first. A model number on the cabinet lets you read the size from the maker's spec sheet, which is more exact than a tape on a roof.
- Measure width and depth at the widest point. Include louver frames, the junction box and any pipe or fitting on the outside of the cabinet.
- Measure height from the bottom of the pan to the top of the lid. Not to the roof or the stand: the drawstring closes under the pan.
- Round width and depth to the nearest inch. A cover up to about 1 in larger is in line with Dial's pairings. Take the next height up, never the next one down.
- Note the draft type, then order down draft or side draft to match.
Straps and fitting
A cover that fits still needs holding down. Dial sells its E-Z Strap kit as two 15 ft x 1 in tie down straps "to reduce heat loss," and Classic Accessories recommends cover straps "in windy conditions" and says to put the cover's open corner away from the prevailing wind. A strap around the cabinet has to be 2 x (width + depth) long:
That is about 9-1/2 ft for a Champion 3000, 11-1/2 ft for a 4001, 13 ft for a 5000, and 15 ft for a MasterCool C71, which uses up a 15 ft strap with nothing left to buckle. A C7112, at 2 x (42 + 52) = 188 in, needs about 15-3/4 ft and a longer strap.
Never run the cooler with the cover on. Classic Accessories prints it as a caution: "For off-season protection only. Operation of your cooler with a cover on it can damage your cooler." Drain the cooler before covering it, as in how to drain a swamp cooler, and take the cover off as the first step of the spring startup.
Where this stops applying
- Other models. The tables cover the cabinets on these sheets. For anything else, measure, or read the cabinet size from the submittal sheet.
- Breezair. Seeley prints only a shipping size for the Icon EXH170 and EXH210 (45-2/3 x 45-2/3 x 37-1/2 in "including pallet"), not the cabinet itself. Dial's Breezair covers, 46 x 46 x 26 in and 46 x 46 x 34 in, are listed for the older EM series. Measure an Icon before buying.
- Portable and window coolers. These are covered or stored differently; see winterizing portable and window coolers.
- Other cover brands. The fit margins here are from Dial's pairings. Another maker's 34 x 34 x 36 in cover may be cut differently, so compare its listed size to your cabinet the same way.
Frequently asked questions
What size cover for a Champion 4001 swamp cooler?
A 34 x 34 x 36 in cover. Champion's spec sheet gives the 4001 a 34-1/8 x 34-1/8 in cabinet that is 34-1/2 in tall, and Dial lists the 4001 on both its 34 x 34 x 36 in down draft cover (8929) and its side draft cover of the same size (8745).
What size cover for a Champion 5000 DD?
Measure first. The current 5000 DD cabinet is 39 x 39 in and 42-7/16 in tall on Champion's sheet. Dial lists its 40 x 40 x 31 in cover (8948) for the Champion 5000, 5500 and 6500 down draft, which would stop about 11 in short of that cabinet; Dial's 40 x 40 x 45 in down draft cover (8950) clears it.
Should a swamp cooler cover be bigger than the cooler?
Only slightly, and mostly in height. In the Dial model pairings that can be checked against a spec sheet, the cover's width and depth are within 1 in of the cabinet. Extra fabric is what the wind catches.
Is there a difference between a down draft and a side draft cooler cover?
Yes. Dial sells them as separate parts, including at the same nominal size: the 34 x 34 x 36 in cover is part 8929 for down draft coolers and part 8745 for side draft coolers. Order the one that matches how your cooler discharges.
How long a strap do I need to hold a cooler cover on?
Long enough to go around the cabinet, which is 2 x (width + depth). That is about 11-1/2 ft for a Champion 4001 and 15 ft for a MasterCool C71. Dial's E-Z Strap kit is two 15 ft x 1 in straps.
Sources and further reading
- Cooler Covers (product category, down draft, side draft and specialty), Dial Manufacturing, Inc.
- 28 W x 28 D x 34 H Cooler Cover, Down Draft (8912), Dial Manufacturing, Inc.
- 34 W x 34 D x 36 H Cooler Cover, Down Draft (8929), Dial Manufacturing, Inc.
- 34 W x 34 D x 40 H Cooler Cover, Side Draft (8750), Dial Manufacturing, Inc.
- 40 W x 40 D Cooler Covers, Down Draft (8948 and 8950), Dial Manufacturing, Inc.
- 42 W x 45 D x 28 H Cooler Cover, Down Draft (8983), Dial Manufacturing, Inc.
- 42 W x 48 D x 35 H Cooler Cover, Down Draft (8984), Dial Manufacturing, Inc.
- 40 W x 40 D x 45 H Cooler Cover, Side Draft (8767), Dial Manufacturing, Inc.
- 42 W x 43 D x 28 H Cooler Cover, Down Draft, Oversized (8902), Dial Manufacturing, Inc.
- E-Z Strap Cover Tie Down Straps (8237), Dial Manufacturing, Inc.
- Champion 3000, 4001 and 5000 DD/SD Specifications and Submittal Data (general specifications), Champion Cooler (Essick Air), hosted by Appliance Factory Parts
- MasterCool AD/AS C51, C5112, C71 and C7112 Specifications and Submittal Data, Champion Cooler, hosted by Appliance Factory Parts
- Champion 75/85 SD, 95 SD, 10/12 SD and 14/21 SD Specifications and Submittal Data, Champion Cooler (Essick Air), hosted by Baker Distributing
- Hessaire DX4800 and DX6800 Owner's Manual (dimensions, cleaning and storage, parts), Hessaire, hosted by The Home Depot
- Technical Specifications: Breezair Icon EXH170, EXH210, Seeley International
- Down Draft Evaporative Cooler Cover Use and Care Guide, Classic Accessories, hosted by The Home Depot