Should You Run a Swamp Cooler During Wildfire Smoke?
No, unless it is a heat emergency. When to switch off by AQI, and how many 4 in MERV 13 filters it takes to cover a Champion cooler, with the airflow they cost.
Short answer
No, not as normal. A swamp cooler has no filter, so it pulls smoke into the house. In a 2023 California field study of homes with no filter on the cooler, indoor PM2.5 rose from about 55% of outdoor levels with the cooler off to 78% with it on. Switch it off when the PM2.5 AQI reaches 101 if anyone in the home is sensitive to smoke, and at 151 for everyone. If the heat is dangerous, EPA says to cover the intakes with 4 inch MERV 13 filters or run the cooler sparingly. A Champion 5000DD takes 16 of the 20 x 25 x 4 size to cover all four sides.
Key takeaways
- A swamp cooler pulls thousands of CFM of unfiltered outdoor air through the house. Wet pads remove only some fine smoke particles: 10 to 40% of PM2.5 in a lab and about 35% in a Texas field study.
- Switch the cooler off at a PM2.5 AQI of 101 (orange) if anyone in the home has asthma, heart or lung disease, or is a child or older adult. Switch it off at 151 (red) for everyone, unless the heat is dangerous.
- EPA's fix for a heat emergency: cover the outside intakes with 4 inch MERV 13 filters, or use the cooler sparingly. Covering a Champion 5000DD fully takes 16 filters of 20 x 25 x 4 in, 4 per side.
- On paper, full coverage costs little air. The filters run at about 80 fpm and add under 0.03 in of resistance, about 1 to 2% of the airflow. In 25 real homes the measured median loss was 15%.
- Pair any cooler use with a HEPA air cleaner in a closed bedroom: about 65 CFM of CADR per 100 sq ft, run on high. In the field study a HEPA cleaner alone did not stop the indoor rise when an unfiltered cooler ran.
On this page
- The terms the answer depends on
- How much smoke a cooler lets in
- When to switch it off: the AQI cutoffs
- Fan only or pump on?
- The filter option: how many filters, and what they cost in airflow
- Fitting the filters
- Pair it with a HEPA air cleaner in a closed bedroom
- Why two answers circulate
- Summary: what to do at each AQI level
- What this does not cover
- Frequently asked questions
No. Do not run a swamp cooler as normal during wildfire smoke, unless the heat itself is dangerous. A swamp cooler has no filter, so it pulls outdoor air, smoke and all, through the house. In a 2023 field study of California homes with no filter on the cooler, indoor fine particles rose from about 55% of the outdoor level with the cooler off to 78% with it on. Switch the cooler off when the PM2.5 AQI reaches 101 if anyone in the home is sensitive to smoke, and at 151 for everyone.
If the house gets dangerously hot, EPA gives two options: cover the cooler's intakes with 4 inch MERV 13 filters, or run it sparingly. This page works out what the filter option takes on a real cooler: how many filters, how fast the air moves through them, and how much airflow they cost.
The terms the answer depends on
A swamp cooler is a direct evaporative cooler. A fan pulls outdoor air through wet pads and pushes it into the house, and the air leaves through open windows or relief vents. Nothing is recirculated, so whatever is in the outdoor air comes in. The how evaporative coolers work guide covers the parts.
PM2.5 is fine particle pollution, made of particles 2.5 microns across or smaller. The 2025 Frontiers paper notes that wildfire smoke now makes up half of the PM2.5 in the Western U.S.
The AQI (Air Quality Index) is EPA's scale for reporting air quality, and AirNow publishes it by pollutant. On a smoke day, read the PM2.5 number.
MERV 13 is a filter rating under ASHRAE Standard 52.2. MERV stands for Minimum Efficiency Reporting Value, and higher numbers catch smaller particles. MERV 13 is the level EPA recommends for smoke.
Static pressure is the resistance the fan pushes against, in inches of water gauge (in w.g.), and every cooler moves less air as it rises. CFM explained covers why. Face velocity is the speed of the air as it enters a filter, in feet per minute (fpm). It is the airflow divided by the filter's face area, and the slower the air, the less resistance the filter adds.
How much smoke a cooler lets in
The best evidence is a 2023 field study of 48 cooler homes in Fresno, Kings and Kern Counties, California, published by Wang and colleagues in 2026. The homes got a HEPA air cleaner, and 25 of them also got MERV 13 filters strapped over the cooler's intakes.
- HEPA cleaner only: the indoor to outdoor ratio of PM2.5 rose from 0.55 with the cooler likely off to 0.78 with it likely on. During wildfire periods that was a 42% jump.
- HEPA cleaner plus cooler filters: the ratio rose only from 0.62 to 0.67 during wildfire periods, an 8% jump.
So a HEPA cleaner did not cancel out an unfiltered cooler, and the filters on the intakes did most of the work.
The pads help a little. The Frontiers paper cites a lab study in which air through moist pads lost 10 to 40% of its PM2.5. A study in 10 Texas homes found about 35%, and the paper then does the math: on a smoke day at 250 micrograms per cubic meter, a 35% cut still leaves more than 150 indoors.
People notice. In the Frontiers survey of 88 cooler households in the San Joaquin Valley, about 47% were dissatisfied with their cooler. The most common reason was that "it brings in dust and air pollution."
When to switch it off: the AQI cutoffs
AirNow says AQI values at or below 100 are "generally thought of as satisfactory." Above 100, air is unhealthy, "at first for certain sensitive groups of people, then for everyone." EPA names the people at greater risk from smoke: children, older adults, and people with heart disease or breathing problems. Its clean room page says local authorities may advise you to stay indoors or set up a clean room when the AQI shows smoke at unhealthy levels and forecast to stay there.
That gives two cutoffs:
- PM2.5 AQI 101 (orange): switch the cooler off if anyone in the home is in a sensitive group. AirNow: "Members of sensitive groups may experience health effects."
- PM2.5 AQI 151 (red): switch it off for everyone. AirNow: "Some members of the general public may experience health effects."
When you switch it off, close the windows you opened for relief air. If your house has up-duct relief vents, close them too (see venting and relief air). Smoke changes through the day, so check again; EPA's factsheet says to open up and air the house out when the air gets better.
Fan only or pump on?
Fan only does not help, because it moves the same outdoor air through the house. The only published figures for pads catching smoke are the wet pad figures above. If you run the cooler in smoke at all, keep the pump on and the filters in place.
The filter option: how many filters, and what they cost in airflow
EPA's clean room page says: "If you have an evaporative cooler and can safely access it, completely cover the outside air intakes with 4-inch-thick high-efficiency (MERV 13) furnace filters or use the cooler sparingly." Nobody publishes the count for a given cooler, but the figures to work it out are all on two data sheets.
Worked example: a Champion 5000DD at 4,530 CFM
Take a Champion 5000DD downdraft cooler with a 3/4 hp motor on a short duct, and suppose its static pressure is 0.2 in. Champion's fan table gives 4,530 CFM there.
Count the filters. Champion's sheet lists four pads, each 36 in high and 33 in wide. A 20 x 25 in filter is smaller than the pad in both directions, so however you turn it, covering one face takes a 2 x 2 grid of four filters. Four faces make 16 filters.
Find the face velocity. AAF Flanders rates its 20 x 25 x 4 PREpleat M13 at 1,050 CFM at 300 fpm. That puts its face area at about 3.47 sq ft, and sixteen filters give 55.6 sq ft. So 4,530 / 55.6 = about 81 fpm.
Find the added resistance. AAF rates the 4 in PREpleat M13 at 0.10 in w.g. at 300 fpm and 0.20 in at 500 fpm. At 81 fpm the resistance is lower than the sheet's first point, and taking it as a straight line from zero to 0.10 at 300 fpm gives no more than 0.027 in. That straight line runs high, since the rated points rise faster than in proportion.
Read the fan table. Champion lists the 5000DD at 4,530 CFM at 0.2 in and 4,280 CFM at 0.3 in. Adding about 0.03 in moves the cooler a quarter of the way along that span. That works out to about 4,460 CFM, a loss of about 1.5%.
Now use one filter per side. Four filters give 13.9 sq ft, with the rest of each face taped shut, so the air enters at about 310 fpm and the filters add about 0.10 in. The fan table drops the cooler to about 4,270 CFM, a loss of about 6%.
The same steps apply to the other Champion cabinets. Pad sizes come from the pad sizes by model page, and airflow is from Champion's fan table at 0.2 in.
| Model | Pad (H x W, in) | Pad faces | Filters to cover | CFM at 0.2 in | Face velocity | Added resistance (4 in) |
|---|---|---|---|---|---|---|
| 3000DD, 1/3 hp | 27 x 22 | 4 | 8 (2 per face) | 1,970 | about 71 fpm | under 0.03 in |
| 4001DD, 1/2 hp | 28 x 27 | 4 | 16 (4 per face) | 3,230 | about 58 fpm | under 0.02 in |
| 5000DD, 3/4 hp | 36 x 33 | 4 | 16 (4 per face) | 4,530 | about 81 fpm | under 0.03 in |
| 5000SD, 3/4 hp | 36 x 33 | 3 | 12 (4 per face) | 4,320 | about 104 fpm | under 0.04 in |
The 3000 pad is 22 in wide, so one filter turned sideways covers its width, and two stacked cover its height. The 4001 pad is 27 by 28 in, just too big for two filters, which fall 2 to 3 in short. You can use two and tape off the strip, but that is partial cover. For a MasterCool, the same rule works per face: the 70-series media, 29 x 41-1/4 in, takes four. The downdraft vs side draft page explains the three-sided SD cabinet.
Three rulings come out of the arithmetic.
- Use 4 in filters, not 1 in. AAF rates its 1 in PREpleat M13 at 0.25 in at 300 fpm, two and a half times the 4 in filter. On the 5000DD with one per side, that alone cuts the airflow by about 13%. The field researchers found 1 inch MERV 13 filters "severely disrupted the airflow."
- Cover the whole face. Full cover keeps the air slow, while one filter per side quadruples the face velocity.
- Plan on 15%, not 1.5%. In 25 homes with airflow measured on the day the filters went on, the median loss was 15% (middle half 11 to 23%). About 70% of homes met the researchers' goal of under 20%. The paper math counts only a clean filter's rated resistance. The measured figure is what real installs lost.
The filters catch less than their MERV rating suggests. Measured on the coolers, new filters removed about 49% of 0.3 to 1 micron particles and 62% of 1 to 2.5 micron particles. After 3 months that fell to about 36% for both.
Fitting the filters
- Only if you can get to the cooler safely. EPA says so in as many words. The researchers list the hazards of fitting filters to rooftop coolers among the challenges they faced.
- Buy 4 in MERV 13. The researchers note these are not readily available in local stores and are considerably more expensive. They put a set of 2 to 6 filters at $60 to $180.
- Strap them over the louvers with bungee cords, airflow arrows pointing into the cooler. Tape the gaps. That is how the field study fitted them.
- Take them off after the smoke. Filters left on for several weeks had water damage and were packed with dust. Colorado's air council warns about monsoon rain on outdoor filters. The monsoon season page covers storm timing.
Pair it with a HEPA air cleaner in a closed bedroom
EPA's clean room is one room with doors and windows closed and a portable air cleaner running. Pick one that makes no ozone, and run it all the time on its highest setting, as EPA advises. EPA's sizing chart asks for 65 CFM of CADR (clean air delivery rate) per 100 sq ft with an 8 ft ceiling. A 12 x 14 ft bedroom is 168 sq ft, so it needs a CADR of about 110 CFM.
Keep the bedroom door shut while the cooler runs, even with filters. In the field study, a HEPA cleaner alone did not stop indoor PM2.5 from climbing when an unfiltered cooler ran. If the house is too hot or too smoky, EPA says to stay somewhere else. A friend's home, a public cleaner air shelter, or a large air-conditioned building such as a mall are all options.
Why two answers circulate
Most pages say "don't run it." Colorado's Regional Air Quality Council answers "Yes," because "first and foremost, please stay cool in the summer heat!" Both are right about different risks. The council goes on to say that "swamp coolers don't have an air filter," so smoke comes in, and it recommends HEPA cleaners and a clean bedroom. The two answers meet in EPA's line: filters on the intakes, or use the cooler sparingly. The council calls heat exposure "a serious public health concern." So heat comes first, and smoke wins whenever the house can stay safely cool without the cooler.
A window or portable AC is usually the better tool on a smoky day. The council says most of them "recirculate the air already inside your room or home." Close the outside damper and seal leaks around the unit, and note that EPA says to use single-hose portable ACs sparingly in smoke. The swamp cooler vs air conditioner page compares the two, and the cooler or heat pump by region page covers places where smoke seasons are long.
Summary: what to do at each AQI level
| PM2.5 AQI (AirNow) | Household with someone sensitive | Everyone else |
|---|---|---|
| 0 to 100 (green, yellow) | Run it | Run it |
| 101 to 150 (orange) | Off; close windows; HEPA cleaner in a closed bedroom | Run it, and check the AQI again later |
| 151 and up (red, purple, maroon) | Off; clean room | Off; clean room |
| Any smoky level, house dangerously hot | Run it with 4 in MERV 13 filters over every intake, or sparingly. Keep the HEPA bedroom. If that is not enough, go to a cleaner air shelter or air-conditioned building. | |
What this does not cover
The airflow figures are a walkthrough of two data sheets, not a test. They assume clean filters at sea level and treat the filters as the only change, while the field study's 15% median is what real coolers lost. Other brands of 4 in MERV 13 rate their resistance differently, so read the sheet for the filter you buy. The Frontiers authors report no significant local wildfire smoke event in 2022 or 2023, so the filters were not tested in heavy smoke. The study shows how much the filters cut the indoor share of PM2.5, not how much smoke anyone breathed. Filters catch particles, not gases, and EPA's air cleaner guide notes no common rating exists for removing gases. Ozone days are a separate issue. Colorado's council suggests running the cooler in the morning and closing up for the afternoon. If anyone in the home has asthma, heart disease or lung disease, EPA says to ask a doctor what to do during smoke events. The allergies and asthma page covers the rest of the cooler's effect on breathing, and pros and cons of swamp coolers weighs smoke against the other trade-offs.
Frequently asked questions
Do swamp cooler pads filter wildfire smoke?
Only partly. Researchers cited in a 2025 Frontiers paper found wet pads removed 10 to 40% of PM2.5 in a lab, and about 35% in 10 Texas homes. The paper notes that on a smoke day with 250 micrograms per cubic meter outside, a 35% cut still leaves more than 150 indoors.
Should I run my swamp cooler on fan only during smoke?
No. Fan only pulls the same outdoor air into the house. The only published figures for pads catching smoke are for wet pads. If you run the cooler during smoke at all, run it with the pump on and filters on the intakes.
What AQI is too high for a swamp cooler?
Use the PM2.5 AQI. At 101 to 150 (orange), switch it off if anyone in the home is sensitive to smoke. At 151 and above (red, purple, maroon), switch it off for everyone unless the heat is dangerous. Then use filters on the intakes or run it sparingly, as EPA advises.
Can I use 1 inch MERV 13 furnace filters on a swamp cooler?
They are a poor choice. AAF Flanders rates its 1 inch MERV 13 at 0.25 in of resistance at 300 fpm, two and a half times the 4 inch version. The field researchers found 1 inch MERV 13 filters severely disrupted cooler airflow and settled on 4 inch filters.
Is a window or portable air conditioner better than a swamp cooler during smoke?
Usually, yes. Colorado's Regional Air Quality Council says most window and portable AC units recirculate room air and don't pull in much outside air. Close the outside damper and seal air leaks around the unit. EPA says to use single-hose portable ACs sparingly in smoke.
How long can MERV 13 filters stay on a swamp cooler?
Only through a smoke event. The field researchers found filters left on for several weeks had water damage and were full of dust, and they advise taking them off after the smoke and storing them. Their removal efficiency also dropped over 3 months.
Sources and further reading
- Create a Clean Room to Protect Indoor Air Quality During a Wildfire (last updated August 18, 2026), U.S. Environmental Protection Agency
- Reduce Your Smoke Exposure (EPA-452/F-26-002, June 2026), U.S. Environmental Protection Agency
- Guide to Air Cleaners in the Home (last updated October 1, 2026), U.S. Environmental Protection Agency
- Air Quality Index (AQI) Basics, AirNow (EPA and partners)
- Swamp coolers and wildfire smoke? Your Colorado indoor air quality questions, answered (July 28, 2026), Regional Air Quality Council, Simple Steps. Better Air.
- Evaporative coolers and wildfire smoke exposure: a climate justice issue in hot, dry regions (Solomon et al., Frontiers in Public Health, 2025), Frontiers in Public Health
- Field Evaluation of Do-It-Yourself Air Filtration Solutions for Evaporative Coolers to Reduce Ambient Particle Infiltration in Homes in Wildfire-Affected Communities (Wang et al., ACS ES&T Air, 2026), ACS ES&T Air, via PubMed Central
- PREpleat M13 (MERV 13) Extended Surface Pleated Panel Filters (AFP-1-384B 11/21), AAF Flanders, retailer copy
- Specifications and Submittal Data: 3000, 4001, 5000 DD and SD (8-08), Champion Cooler