Do AC Misters Work?
Lab tests of AC condenser misters measured 2 to 6% less power at 105 F. Pads in front of the coil did far better. Inlet temps for Phoenix, Las Vegas and more.
Short answer
A little. In a Southern California Edison lab test, three store-bought mister kits on a 3-ton AC condenser cut its power draw by 1.9 to 5.8 percent at 105 F. They captured only 8 to 25 percent of the cooling the air had to give. Pre-coolers that wet a pad in front of the coil reached 60 to 75 percent in a later test. Those are the products behind the 10 to 30 percent savings claims.
Key takeaways
- An AC mister sprays water into the air going into your outdoor AC unit. Cooler air there means the compressor works less. It never touches the air inside your house.
- In SCE's 2012 lab test, three off-the-shelf mister kits averaged 8, 20 and 25 percent evaporative effectiveness and cut power 1.9 to 5.8 percent at 105 F.
- Pad-type pre-coolers tested in 2015 reached 60 to 75 percent. ORNL modeled an 81.6 percent pad at 24 to 26 percent annual energy savings for R-410A rooftop units in Phoenix and Las Vegas.
- Worked from the lab's own figures, the kits saved 0.02 to 0.05 kWh per gallon of water. At ORNL's Phoenix water price, two of the three needed power worth 14 cents a kWh or more just to break even.
- Sprays that wet the coil left scale on the unit with hard water, and mist nozzles clogged. Carrier's and Oxbox's warranties exclude damage from add-on parts and corrosive materials.
On this page
- What an AC mister is, and what "effectiveness" means
- What the lab tests measured
- Mist on the fins versus a pad in front of the coil
- How much cooler the coil gets in Phoenix, Las Vegas and Albuquerque
- The numbers behind "10 to 30 percent"
- Water: what each gallon buys
- Hard water and scale on the coil
- What the AC warranty says
- What this page does not cover
- Frequently asked questions
AC misters work, but much less than the boxes suggest. Southern California Edison paid the Western Cooling Efficiency Center at UC Davis to test three store-bought kits on a 3-ton AC condenser. At 105 F, they cut its power draw by 1.9, 5.7 and 5.8 percent. Pre-coolers that run water down a pad in front of the coil did far better in a later test. The 10 to 30 percent savings you see quoted come from those pads, modeled on big rooftop units. They are not mister kits.
Below are the measured numbers, the cooling each type gives in three desert cities, the water bill, and the scale and warranty risks.
What an AC mister is, and what "effectiveness" means
Central air has an outdoor unit, the condenser. Its fan pulls outside air across a finned coil. That air carries away the heat taken from your house. The hotter that air is, the harder the compressor works. An AC mister sprays fine water droplets into that air, or straight onto the coil. As the water evaporates, it cools the air before it reaches the fins. The broader name for any add-on that does this is an evaporative pre-cooler. Some use mist nozzles. Others drip water down a pad wrapped around the coil, the way a swamp cooler pad works.
None of this cools your house directly. The cooled air goes through the outdoor coil and out the top of the unit. Your indoor air never touches it and gets no extra humidity. The only gain is a compressor that draws less power and cools a little better.
How well a pre-cooler works is measured the same way as a swamp cooler pad:
- Wet bulb temperature
- The lowest temperature evaporating water can bring the air to. Dry air has a wet bulb far below its air temperature. See wet bulb temperature explained.
- Evaporative effectiveness
- The share of the gap between air temperature and wet bulb that the device actually removes. SCE's example: at 100 F and a 70 F wet bulb, a 50 percent pre-cooler delivers 85 F air. On a swamp cooler the same number is called saturation efficiency.
- Water-use effectiveness
- The share of the water used that evaporates before the coil and does some cooling. The rest drips off, misses or blows through.
What the lab tests measured
SCE's 2012 test (report HT.11.SCE.021) used a Goodman 3-ton condensing unit in a sealed test room. It tried three kits sold for homes and light commercial units. Kit A sprays water straight onto the coil. Kit B wraps the unit in a fiberglass blanket and mists into it. Kit C uses three small mist nozzles that turn on when the condenser fan blows. The report found each kit's effectiveness "between 0-40%," depending on the method. On its main method, the averages were low.
| Kit | How it wets the air | Average effectiveness | Power saved at 105 F / 73 F wet bulb | Water used | Water that did cooling |
|---|---|---|---|---|---|
| A | Sprays onto the coil, pulses more as it gets hotter | 25% | 5.8% | 7.89 gal/h | 20% |
| B | Mist into a fiberglass blanket around the unit | 20% | 5.7% | 4.94 gal/h | 31% |
| C | Three mist nozzles, on whenever the fan runs | 8% | 1.9% | 1.21 gal/h | 51% |
The report is blunt: these "were not particularly effective." But it warns they are not the whole market. In its words, "field test studies have demonstrated 80% effectiveness in other products."
The follow-up test, ET13SCE1020 (2015), tried five commercial pre-coolers on a 4-ton rooftop unit. Their effectiveness ran from about 20 to 80 percent. The three best clustered between 60 and 75 percent. One of them runs water from a pump down 8 in cellulose media, like the pad in a swamp cooler. The two weakest, including one that sprays the coil, stayed below 50 percent.
Mist on the fins versus a pad in front of the coil
The best results came from wetting a pad, not from spraying water at the coil. A pad holds water where the air has time to pick it up. A mist has a split second, and much of it lands on the fins or passes through.
Spraying the coil has its own effect. SCE found that water evaporating on the coil helps the coil shed heat. So kit A saved more power than its air cooling alone would explain. That is why its effectiveness came out higher by the power method than by the air method. It is also why that design wets the fins every time it runs.
A pad has a cost when it is dry. Air has to push through it. In the 2015 test, two of the pads cost the unit about 1 percent of its efficiency when dry. A third, a 1 in foamed polyester pad, cost 10.5 percent. Kit B's blanket cut the unit's airflow from 2,465 to 2,388 cubic feet per minute and cost about 8 points of effectiveness. If a pre-cooler shuts off its water in mild weather but leaves the pad in place, that loss runs all spring. The 8 in versus 12 in media page covers how pad depth trades cooling against airflow on a swamp cooler.
How much cooler the coil gets in Phoenix, Las Vegas and Albuquerque
Here are the formula above and the design days from the site's climate index. The design day is a hot day seen only about 1 percent of the hours in a year. Phoenix is 110 F with a 70 F wet bulb. Las Vegas is 106 F and 66 F. Albuquerque is 94 F and 60 F. Use the cooling temperature calculator to get the wet bulb for your own afternoon.
| City (dry bulb / wet bulb) | No pre-cooler | 8% (kit C) | 25% (kit A) | 70% (good pad) | 80% (best field result) |
|---|---|---|---|---|---|
| Phoenix (110 / 70 F) | 110 F | 106.8 F | 100 F | 82 F | 78 F |
| Las Vegas (106 / 66 F) | 106 F | 102.8 F | 96 F | 78 F | 74 F |
| Albuquerque (94 / 60 F) | 94 F | 91.3 F | 85.5 F | 70.2 F | 66.8 F |
A mister kit takes 3 to 10 F off. A good pad takes 24 to 32 F off, enough to make a Phoenix afternoon look like a mild morning to the coil. In SCE's lab, the 3-ton unit drew about 0.02 kW more for every degree of outdoor air between 64 and 105 F. So 10 F is worth about 0.2 kW on a unit that size.
Humid air is a different story. At SCE's warm-humid test point, 82 F with a 73 F wet bulb, there are only 9 F to work with. All three kits did their worst there.
The numbers behind "10 to 30 percent"
Both big savings figures are models of good pads on commercial rooftop units, not measurements of mister kits.
- SCE's model (2012). It took an 80 percent pre-cooler on an average rooftop unit in SCE's service area. Energy savings came to 3 to 25 percent and peak demand savings to 10 to 30 percent, by climate zone. That is 30 to 300 kWh a year and 0.1 to 0.33 kW per ton.
- ORNL's model (2019). Oak Ridge National Laboratory simulated an 81.6 percent pad, the figure a maker gave for a standard 8 in commercial pad. For a medium office with R-410A units, annual savings were 24.2 percent in Phoenix, 26.0 percent in Las Vegas and 16.1 percent in Albuquerque. Peak power fell 38.0, 39.0 and 29.5 percent. With older R-22 units, the same pad saved only 13.3, 13.5 and 5.1 percent a year.
So both answers you find online are partly right. A real pad pre-cooler, sized and wetted properly, does save in the range people quote. A clip-on mist kit is a different product, and its measured result was a few percent.
Water: what each gallon buys
Every degree of cooling costs water. The site's evaporation rule for swamp coolers works for condenser air too. Gallons per hour equal airflow in CFM times the temperature drop, divided by 8,186. SCE puts typical condenser airflow at 800 CFM per ton. At 70 percent in Phoenix, a pad evaporates about 2.7 gallons per hour per ton, or 8.2 gallons per hour on a 3-ton unit. Pads that reuse their water also need a steady drain, called bleed-off, to keep scale down. The 2015 report says that may add 10 to 50 percent. A whole-house swamp cooler uses water at about the same rate, as the water usage guide shows.
Worked example: is a mist kit worth its water?
Take the lab's 3-ton unit at the 105 F test point. Its baseline line puts it at about 2.9 kW. Kit A saved 5.8 percent, or 0.17 kW. It used 7.89 gallons an hour on average. That is 0.17 / 7.89 = 0.021 kWh saved per gallon. Worked the same way, kit B gives 0.033 kWh per gallon and kit C 0.046.
Now use the Phoenix rates in ORNL's paper: 124 cents per cubic meter of water, about 0.47 cents a gallon. To break even, a kWh has to be worth 0.47 / 0.021 = 22 cents for kit A. For kit B it is 14 cents and for kit C 10 cents. ORNL's Phoenix power price was 10.1 cents.
Suppose instead a pad reached 70 percent on the same unit. It would cool the air 22.4 F, to about 82.6 F. The lab's baseline line drops by about 0.46 kW over that range. The 2015 pad product's pump drew 117 W, so the net is about 0.35 kW. The pad would evaporate about 2,465 x 22.4 / 8,186 = 6.7 gallons an hour, or up to about 10 with bleed-off. That is 0.035 to 0.052 kWh per gallon, a break-even of about 9 to 13 cents. The pad cools far more than any kit, but the water still has to be cheap next to your power.
Put in your own water and power rates. Kits B and C spray at a steady rate, so their water use does not change with the heat. Kit A pulses more when it is hot, so its real use at 105 F is likely higher than its average.
Hard water and scale on the coil
Every gallon that evaporates leaves its minerals behind. On a swamp cooler they land on a pad you replace. With a mister, they land on the condenser fins or on small nozzles. SCE ran two kits on hard well water for about 10 to 15 hours while building the lab. Kit A, the coil sprayer, left scale on the outside of the unit. The report calls that "a significant and expected concern for a design that sprays directly onto the coil." Kit B's tiny nozzles clogged and needed brushing, vinegar soaks or replacement. They were worst after sitting off overnight, which is how a home system runs every day.
The 2015 report says the same of its coil sprayer. It "requires water treatment such as softening or osmosis for continuous use." The one mist design among the top three is meant to evaporate its water before the coil. Even so, its maker recommends softening or possibly reverse osmosis to protect the coil from stray droplets. Both labs ran their formal tests on reverse osmosis water, so their numbers do not show what a season of hard water does. Treatment and removal are covered in scale removal and prevention and bleed-off and water quality.
What the AC warranty says
We read the outdoor unit warranties from Carrier, Oxbox (a Trane Technologies brand) and Goodman. None mentions misters or pre-coolers by name. Two kinds of clause still reach them.
- Carrier, condensing units with R-454B, edition 08/26. It does not cover "Parts or equipment not supplied or designated by Company, or damages resulting from their use." It also excludes damage from "corrosive environments."
- Oxbox, units shipped from March 1, 2024. It excludes damage caused by "any third party product, service, or system connected or used in conjunction with the Products." It also excludes "contact with corrosive materials," a list that ends with "other damaging substances or chemicals."
Goodman's 2014 warranty for its SSX14 and SSX16 units has the same idea. It excludes "Parts or accessories not supplied or designated by the manufacturer." A mister is a third party part connected to the unit. If scale or corrosion damages the coil, a claim would likely run into these clauses.
What this page does not cover
The lab numbers come from one 3-ton R-22 condenser and one 4-ton rooftop unit. The savings models are for commercial buildings. Your house runs different hours, and newer units use R-410A or R-454B. ORNL found R-410A gains more from pre-cooling than R-22. It did not model R-454B. The city temperatures use design-day figures, not a typical summer afternoon. The water math leaves out sewer charges and the water used to soften or filter the supply. None of this checks whether your unit's airflow, coil or warranty terms allow a pre-cooler. Ask your installer before adding one. If you want the house itself cooled by evaporation, that is a swamp cooler, compared in swamp cooler vs air conditioner.
Frequently asked questions
How much does an AC mister lower the air temperature?
It depends on how much water evaporates before the coil. On a Phoenix design day (110 F, 70 F wet bulb), a kit at 25 percent effectiveness cools the air 10 F, to 100 F. A pad at 70 percent cools it 28 F, to 82 F.
Do AC misters damage the condenser?
They can. In SCE's lab, a kit that sprayed straight onto the coil left visible scale on the unit after about 10 to 15 hours on hard well water. A later report says a spray-on-coil design needs softened or reverse osmosis water for continuous use.
Will a mister void my AC warranty?
No warranty we read names misters. But Carrier's 2026 condensing unit warranty excludes parts not supplied by Carrier and damage from their use. The Oxbox warranty excludes damage caused by any third party product connected to the unit. A scale or corrosion claim would likely meet those clauses.
How much water does an AC mister use?
The three kits in SCE's test used 1.21, 4.94 and 7.89 gallons per hour on a 3-ton unit. Only 20 to 51 percent of that water did any cooling. The rest dripped off or blew through.
Do AC misters work in humid weather?
Hardly. At 82 F with a 73 F wet bulb, the air has only 9 F of cooling to give. In SCE's lab, all three kits did their worst at that point, with effectiveness from about zero for kits B and C to 28 percent for kit A.
Sources and further reading
- Condenser Air Evaporative Pre-Cooler Test Protocol, HT.11.SCE.019/HT.11.SCE.021 (December 2012), Southern California Edison Design & Engineering Services, with UC Davis Western Cooling Efficiency Center, via ETCC
- Develop and Test Protocols for Evaporative Pre-Coolers for RTU Retrofit Initiative (ET13SCE1020), project page, Emerging Technologies Coordinating Council
- Evaporative Condenser Air Pre-Coolers, ET13SCE1020 (December 2015), full report, Southern California Edison Emerging Products, hosted by UC Davis Western Cooling Efficiency Center
- Energy and Economics Analyses of Condenser Evaporative Precooling for Various Climates, Buildings and Refrigerants (Shen, New and Ally, Energies 12(11):2079, 2019), Oak Ridge National Laboratory
- Energy and Economics Analyses of Condenser Evaporative Precooling, full text, U.S. Department of Energy, OSTI
- Limited Warranty for Air Conditioner & Heat Pump Condensing Units with Puron Advance (R-454B) Refrigerant, ACHP-C454-02WAR (edition 08/26), Carrier Corporation
- Limited Warranty, models SSX14, SSX16, SSZ14, SSZ16 (PWCACHPCG, 6/2014), Goodman Manufacturing Company
- Oxbox Limited Warranty (products shipped on or after March 1, 2024), TwentyThreeC, LLC (Trane Technologies)