Motors, Belts and Blowers

What Size Pulley Does My Swamp Cooler Motor Need?

Swamp cooler motor pulley sizes by horsepower and by model: 3-1/4 in adjustable for 1/3 hp, 3-1/2 in for 1/2 hp, Champion OEM part numbers, fixed pulley sizes, and the diameter the belt actually runs at.

Short answer

Use the pulley the cooler maker lists for your model and motor. Without that, Dial's adjustable pulleys run 3-1/4 in for 1/3 hp, 3-1/2 in for 1/2 hp, 3-3/4 in for 1/2 or 3/4 hp and 4 in for 1 hp. The bore must match the motor shaft, 1/2 or 5/8 in. The labeled size is the closed diameter: opened 2-1/2 to 5 turns, the belt runs at about 2.2 to 3.1 in.

Key takeaways

  • An adjustable pulley is named by its closed diameter. Champion's blower speeds put the working diameter of the 3-1/4 in pulley on a 3000's 1/3 hp drive at about 2.3 to 2.8 in.
  • That is why fixed pulleys for the same motor are a full inch smaller: Dial sells 2-1/4 in for 1/3 hp, 2-3/4 in for 1/2 hp and 3 in for 3/4 hp.
  • Champion fits a 3-1/4 in pulley (110277) to the 3000 and a 3-1/2 in (110278) to the 4001 and 5000, both 1/2 in bore. Its own manuals do not follow the generic horsepower chart on every cabinet.
  • More duct resistance lets the pulley close further, not less. Hessaire's instructions open it about 2-1/2 turns on a ducted house and 4 to 5 with no ducts.
  • If the motor still cycles on overload with the pulley fully open, Dial's instruction is to fit the next smaller pulley, never a larger one.
On this page
  1. Pulley size by motor horsepower
  2. Champion's OEM pulleys by model
  3. The label is the closed size, not the working size
  4. More ducts, more closed: the setting most people get backwards
  5. Fixed or adjustable?
  6. How to set an adjustable pulley to the motor
  7. Why a bigger pulley is the wrong fix
  8. Where this stops applying
  9. Frequently asked questions

Your motor needs the pulley the cooler maker lists for that model and motor, and failing that, the size matched to its horsepower: Dial's adjustable pulleys run 3-1/4 in for 1/3 hp, 3-1/2 in for 1/2 hp, 3-3/4 in for 1/2 or 3/4 hp and 4 in for 1 hp, with a bore that fits the shaft. Champion fits a 3-1/4 in pulley to its 3000 series and a 3-1/2 in to the 4001 and 5000. The catch is that the number on the label is the closed diameter. Opened the way the makers require, the belt runs on something closer to 2-1/4 to 3 in, and the tables below show where that figure comes from.

Pulley size by motor horsepower

Two parts makers publish a pulley-by-horsepower chart: Dial, on its product pages, and Hessaire in the instruction sheet packed with its replacement motors. They agree on the adjustable sizes and differ by a quarter inch here and there on the fixed ones.

Motor pulley size by horsepower (aftermarket charts)
MotorDial adjustableHessaire adjustableDial fixedHessaire fixed
1/3 hp3-1/4 in (6122 to 6124; 6129 in 5/8 bore)3-1/4 in2-1/4 in (6215)2-1/4 to 2-1/2 in
1/2 hp3-1/2 in (6143 to 6145; 6146 in 5/8 bore), or 3-3/4 in3-1/2 to 3-3/4 in2-3/4 in (6244)2-1/2 to 2-3/4 in
3/4 hp3-3/4 in (6148 to 6151; 6153 in 5/8 bore)3-3/4 in3 in (6264)3 to 3-1/4 in
1 hp4 in (6170 in 1/2 bore; 6172, 6173 in 5/8 bore)4 in, single inlet coolers onlyNot listed3-1/4 to 3-1/2 in

Dial lists every fixed pulley with a 1/2 in bore. Hessaire's chart gives 1/2 in bores up to 3/4 hp and 5/8 in for 1 hp, but that is a statement about its own motors, not a rule. Dial sells the 1 hp adjustable in both bores, and RSD's listings for AOS cooler motors show 1/2 in shafts on both the 1/2 hp SVB2054H and the 1 hp SV2104L, both 56Z frame. Measure the shaft, or read it off the motor, and buy that bore. The replacement motor guide covers frame and shaft matching in more detail.

Champion's OEM pulleys by model

Where the cooler maker publishes a part, it overrides the chart above. Champion prints the motor pulley in its submittal sheet and owner's manuals, and its SM manual describes these parts as 1/2 in bore with an adjustable outside diameter.

Champion OEM motor and blower pulleys by model
CoolerMotorMotor pulleyBlower pulley
3000 DD/SD1/3 hp110277, 3-1/4 in110274, 7 in
4001 DD/SD1/3 or 1/2 hp110278, 3-1/2 in110275, 10 in (listed for 4000/4001 DD)
5000 DD/SD1/2 or 3/4 hp110278, 3-1/2 inNot printed on the sheet
3000 RLD, 3001 RLD21/3 hp / 1/2 hp110277 / 110278110274
4000 RLD, 4001 RLD21/3 / 1/2 / 3/4 hp110277 / 110278 / 110279-001110275
5000 RLD, 5001 RLD21/2 / 3/4 / 1 hp110277 / 110278 / 110279110276, 12 in
3000 SM1/3 hp110277110274
4000 SM, 4500 SM1/3 hp, 1/2 hp110278110275
5500 SM, 6500 SM1/2 hp, 3/4 hp110278110276

Read across the rows and the generic chart breaks down. The 4000 SM puts a 3-1/2 in pulley on a 1/3 hp motor, where Dial would say 3-1/4. The 5000 RLD puts a 3-1/4 in on a 1/2 hp motor and a 3-1/2 in on a 3/4 hp, both a step smaller than Dial's sizes. The 6500 SM runs its 3/4 hp motor on a 3-1/2 in. The motor pulley only means something against the blower pulley it drives, and a 12 in blower pulley turns the same motor pulley into a slower blower than a 7 in one does. So the model comes first and horsepower second. If you do not know which motor your cabinet allows, start with what size motor a swamp cooler needs; the same data plate also picks the belt in the belt size chart. Champion's manual does not print a diameter for 110279 or 110279-001, so for those, order by part number.

The label is the closed size, not the working size

This is why the two charts look inconsistent: a 1/3 hp motor gets 3-1/4 in adjustable but 2-1/4 in fixed. An adjustable pulley is two flanges on a threaded hub. Screwed shut, the belt rides near the rim and the pulley acts at its full labeled diameter. Each turn outward widens the V and lets the belt sink toward the hub, so it acts like a smaller pulley.

Two cross-sections of an adjustable pulley: closed, the belt sits near the rim far from the shaft; opened, the groove is wider and the belt sits near the hub, much closer to the shaft
The same adjustable pulley closed and opened. The belt's distance from the shaft is the radius that sets blower speed, so opening the flanges makes a 3-1/4 in pulley drive like a much smaller one.

None of the makers is shipping these closed. Dial's instruction for its variable pulleys is that they must be opened 2-1/2 to 5 full turns, depending on air resistance, or the motor will overheat. Essick tells installers to close the pulley fully and then open it 3 or 4 turns before fitting it. Champion's manuals go further and say to start at the least diameter, which is fully open, and work up.

How far below the label the belt really runs can be worked out from Champion's submittal sheet, which prints blower speed alongside airflow at each step of static pressure. With a 1,725 rpm motor (the high speed of the usual two-speed cooler motor, 1725/1140 on RSD's listings) and the blower pulley sizes from Champion's parts descriptions, the effective motor pulley diameter is blower rpm x blower pulley diameter / 1,725.

Effective motor pulley diameter from Champion's rated blower speeds
Cooler and motorLabeled pulleyBlower rpm, 0 to 0.3 inWorking diameter, 0 to 0.3 inAt highest rated static
3000 DD, 1/3 hp (7 in blower pulley)3-1/4 in562 to 6302.28 to 2.56 in2.80 in at 0.5 in
3000 SD, 1/3 hp3-1/4 in574 to 6452.33 to 2.62 in2.70 in at 0.4 in
4001 DD, 1/3 hp (10 in blower pulley)3-1/2 in376 to 4402.18 to 2.55 inNot rated past 0.3 in
4001 DD, 1/2 hp3-1/2 in443 to 4942.57 to 2.86 in3.12 in at 0.5 in

The figures are approximate: they use the blower pulleys' outside diameters and ignore belt slip. Even so, the pattern is clear. The 3-1/4 and 3-1/2 in pulleys never run at their labeled size on these drives: even at the highest static pressure Champion rates, they stay 0.38 to 0.55 in below it. And the bottom of each range lands on the fixed sizes: 2.18 to 2.33 in for the 1/3 hp drives against Dial's 2-1/4 in fixed pulley, 2.57 in for the 1/2 hp 4001 DD against Hessaire's 2-1/2 to 2-3/4 in. The fixed pulleys are the adjustable ones locked at their no-duct setting.

More ducts, more closed: the setting most people get backwards

Look down any column of Champion's sheet and blower speed rises as static pressure rises: the 3000 DD goes from 562 rpm with no duct to 690 rpm at 0.5 in, on the same 1/3 hp motor. A blower pushing against resistance moves less air and so takes less power at a given speed, which leaves room to spin it faster. Hessaire's motor instructions turn this into a setting: open the pulley about 2-1/2 turns for a house with several ducts, 3 to 4 turns with few ducts, and 4 to 5 turns with no ducts.

So the cooler that most needs an open pulley is the one with the least in its way: a side-draft blowing straight into a room, or a downdraft into a single short drop with the windows wide open. A cooler feeding long branch ducts can usually run the pulley more closed without overloading. The same logic explains a common surprise: clean a badly clogged duct, add a window opening or swap undersized grilles, and a motor that ran fine can start cycling, because the resistance it was relying on has gone. The ductwork guide and venting and relief air cover the resistance side, and CFM explained covers what static pressure is.

Fixed or adjustable?

Dial describes its fixed pulleys as sized to avoid overloading cooler motors installed without an ammeter. That is the honest trade: a fixed pulley sits at the safe end of the range and gives away whatever airflow your ducts would have allowed. On a 3000 DD running against 0.3 in of static pressure, Champion's figures put the working diameter near 2.56 in, and a 2-1/4 in fixed pulley turns the blower about 12 percent slower than that. Airflow falls roughly in step with blower speed on the same duct system, so that is roughly 12 percent less air.

Use a fixed pulley if you cannot measure amps and the cooler has no ducts to speak of, which is where its size matches anyway. Use an adjustable pulley everywhere else, and set it with a meter.

How to set an adjustable pulley to the motor

All three manufacturers set the pulley by motor current, not by turn count. Champion's procedure, from its RLD manual, with Essick's half-turn steps:

  1. Start fully open. Champion: adjust the drive pulley to the least diameter after the unit is completely installed, then set belt tension.
  2. Run it as it will be used. Install all pad frames, start the pump and let the pads wet before reading.
  3. Read the amps. Clamp an ammeter on the motor lead with the blower on high and compare it with the nameplate full-load amps.
  4. Close in half turns. If the draw is under the nameplate, kill power, close the movable flange half a turn and line its set screw up on the flat of the hub. Essick works in the same half-turn steps, in either direction.
  5. Re-tension and repeat. A larger working diameter tightens the belt, so reset tension at the motor mount each time. Essick says not to use the motor pulley to adjust belt tension.
  6. Stop at nameplate. Champion: do not operate the cooler with a larger amperage draw than specified on the motor plate. Hessaire's figure is equal to or less than nameplate amps.

The step-by-step for loosening the flange, aligning the pulleys and checking tension is in belt and pulley adjustment.

When to go smaller: If the motor stops and restarts on its overload with the pulley already fully open, Dial's instruction is to fit the next size smaller pulley. Before buying one, rule out the other things that make a motor cycle: a dragging bearing, an overtight belt or a failing motor. See swamp cooler motor not running before buying parts.

Why a bigger pulley is the wrong fix

Every source here says the same thing in different words. Dial: always use the pulley size recommended by the cooler manufacturer. Hessaire: do not use a larger pulley size, because too large a motor pulley will overload the motor and cause it to cycle on and off. Champion: increasing motor pulley diameter increases amperage draw. A larger pulley turns the blower faster, and fan power climbs far faster than speed does, so a modest gain in air costs a large jump in current.

If the cooler is short of air with its pulley at nameplate amps, the larger motor the cabinet allows is the fix, together with the pulley that motor is listed with. Champion's 4001 DD shows what that buys: 3,064 CFM against 2,240 CFM at 0.3 in. Check the circuit before you upgrade; the breaker and wire size guide gives the amps for each step.

Where this stops applying

The charts cover belt-drive residential coolers from about 1/3 to 1 hp. Direct-drive coolers, including most portables and many window units, have no motor pulley; the blower wheel sits on the motor shaft. Commercial cabinets select pulleys differently: Champion's AS/AD 100 and 150 use matched pulley and belt kits chosen by motor horsepower, shaft bore and static pressure, with part numbers rather than a single diameter. Hessaire limits its 1 hp row to single inlet coolers. For any brand whose maker lists a pulley for your model, that listing outranks every figure on this page.

Two-speed motors drop to about 1,140 rpm on low, so low speed runs the blower roughly a third slower on the same pulley; set the pulley on high, where the load is greatest. The wiring for both speeds is in two-speed motor wiring.

Frequently asked questions

What size pulley goes on a 1/3 hp swamp cooler motor?

A 3-1/4 in adjustable pulley, or a 2-1/4 in fixed one, both with a bore that fits the motor shaft (usually 1/2 in). Dial and Hessaire give the same adjustable size; Hessaire's fixed range is 2-1/4 to 2-1/2 in. Champion fits the 3-1/4 in pulley, part 110277, to its 3000 series.

What size pulley does a 1/2 hp swamp cooler motor take?

A 3-1/2 in adjustable pulley (Dial lists 3-1/2 in, Hessaire 3-1/2 to 3-3/4 in) or a 2-1/2 to 2-3/4 in fixed pulley. Champion's 4001 DD and SD use the 3-1/2 in pulley, part 110278, with a 1/2 in bore.

Will a bigger pulley make my swamp cooler blow more air?

It spins the blower faster, but the motor pays for it. Champion's manuals say a larger motor pulley diameter increases amperage draw, and Dial and Hessaire both warn against using a larger pulley than the cooler maker recommends. Close the existing adjustable pulley in half-turn steps and stop at nameplate amps instead.

Is the pulley size the outside diameter?

On an adjustable pulley, the listed size is the outside diameter with the flanges closed. Once opened to the 2-1/2 to 5 turns Dial requires, the belt rides lower in the groove and the working diameter is well below the label, which is why fixed pulleys for the same motor are about an inch smaller.

Does pulley bore depend on horsepower?

No, it depends on the motor shaft. Hessaire's chart pairs 5/8 in bores with 1 hp motors, but Dial sells its 1 hp pulley in both 1/2 and 5/8 in bores, and AOS 1 hp cooler motors have 1/2 in shafts. Measure the shaft or read it off the motor listing.

Sources and further reading

  1. Variable Motor Pulley, parts 6122 to 6173 (HP, diameter and bore table; opening instructions), Dial Manufacturing
  2. Fixed Motor Pulley, parts 6215 to 6264 (HP, diameter and bore table), Dial Manufacturing
  3. Hessaire Evaporative Cooler Motor Instruction (motor pulley selection and adjustment), Hessaire (hosted by The Home Depot)
  4. Champion 3000, 4001 and 5000 DD/SD Specifications and Submittal Data (motor pulley part, CFM and blower RPM at static pressure), Champion Cooler (hosted by Appliance Factory Parts)
  5. Champion 3000/4000/5000 RLD and RLD2 Owner's Manual (motor specifications, amperage draw and belt tension, parts list), Champion Cooler (hosted by Appliance Factory Parts)
  6. Champion 3000, 4000, 4500, 5500 and 6500 SM Owner's Manual (motor specifications, parts list), Champion Cooler (hosted by Appliance Factory Parts)
  7. Essick 15000 Owner's Manual (motor pulley installation, belt adjustment, start up), Essick Air (hosted by Appliance Factory Parts)
  8. Champion Cooler 110278 Pulley, Motor, 3-1/2 in, 1/2 in bore (and 110277 motor pulley 3-1/4 x 1/2 for 3000 DD), Parts Town
  9. Champion Cooler blower pulleys 110274 (7 x 1, 3000 SD/SM/DD) and 110275 (10 x 1, 4000/4001DD), Parts Town
  10. Models AS/AD 100, AS/AD 150: specifications and submittal data (pulley-belt kit selection), Champion Cooler (hosted by Appliance Factory Parts)
  11. Evaporative cooler motors (AOS SVB2054H and SV2104L: HP, RPM, frame, shaft), RSD